What do you guys think about this DIY stand plan i got from another Fourms thread? 
I am going to try it for my 300gallon acrylic tank using 2x8's and adding some center supports. 
My dimensions are 80x24x36.
View attachment 473191
"The basic principle of the design is two box frames connected by four legs. The upper one supports the tank and transfers the load to the legs. The legs are made of several pieces of 2X4 to assist in construction and sheething the stand in plywood for strength and cosmetics. The bottom frame transmits the load of the tank into the floor.
Design notes:
*The plan for this stand consists of 21 pieces. Like color pieces are the same length and of the same board size.
*The box frames are screwed together first, then the legs are built off the bottom frame, the top frame is then placed on top and secured to the legs.
*The green pieces are screw strips. These provide limited load strength but serve to make assembly easier and help keep the stand square.
*The blue piece between the upper rails (red) works to keep the upper rails from twisting.
Ok, now to the cut list:
First off: The calculations below are based off of a stand that is "W" inches wide X "D" inches front-to-back X "H" inches high.
(2) Red - Upper Rails: Length = W
These will be sized according to length: 2X4 for 48" or less for smaller tanks (Rule of thumb is 75g-90g); 2X6 up to 72" with 125g-150g being acceptable; For longer spans and larger tanks 2X8s are recommended.
(2) Yellow - Upper Ends: Length = D-3"
Theses will be made of the same material as the upper rails.
(4) Green - Screw Strips: Length = H-2"
These 2X4s are shorter then the tank is tall.
(8) Purple - Uprights: Length varies:
- 2X4 Upper Rails: Length = H -7"
- 2X6 Upper Rails: Length = H-9"
- 2X8 Upper Rails: Length = H-10.75"
These 2X4s support the weight of the tank. The ones on the short sides of the stand provide a flat surface for attaching a plywood facing and while they do provide some strength, they are optional.
(2) Orange - Bottom Rails: Length = W
These 2X4s act to spread the weight of the tank over a larger area.
(3) Blue - Bottom Ends: Length = D-3"
Covering the sides of the stand with plywood will help to stiffen the stand against twisting and shifting. Doors can be mounted to the legs as desired.
So there it is. 21 pieces in 6 lenghts equals a tank stand that should fit the bill for most people. There are other plans out there but this is a simple design using simple tools and common wood sizes. It may not suit everyone's application but it should fit the bill for most common size tanks.
Things to note:
A 2X4 is actually 1.5" X 3.5"; a 2X6 is actually 1.5" X 5.5"; and a 2X8 is actually 1.5" X 7.25".
Making a beam made up of two boards side by side is twice as strong as each of the individual boards. For a 48" span, a 2X4 supporting 1000#s deflects 0.269" while a 2X6 only deflects 0.069" and a 2X8 deflects 0.030". That said, it is much better to go up in size then it is to double up.
When assembling the stand, be sure all of the pieces have square cut ends and that they are as straight as possible. If one of the long boards for the top frame (red above) has a crown (bows up when stood on edge), be sure to place the crown up. Glue will help bond the pieces together and coated decking screws will resist rusting. Clamping the pieces together and pre-drilling the holes will help make assembly easier.
Pocket drilling the legs (purple) can eliminate the need for the screw strip (green) but I would make sure to skin the stand on three sides to keep it from racking/twisting. Also, be sure to screw both leg pieces together on the corner for added strength."
HERE IS LINK TO ENTIRE THREAD:http://reefcentral.com/forums/showthread.php?s=&threadid=1169964&perpage=25&pagenumber=1
Please give me your feedback.
I am going to try it for my 300gallon acrylic tank using 2x8's and adding some center supports. My dimensions are 80x24x36.View attachment 473191
"The basic principle of the design is two box frames connected by four legs. The upper one supports the tank and transfers the load to the legs. The legs are made of several pieces of 2X4 to assist in construction and sheething the stand in plywood for strength and cosmetics. The bottom frame transmits the load of the tank into the floor.
Design notes:
*The plan for this stand consists of 21 pieces. Like color pieces are the same length and of the same board size.
*The box frames are screwed together first, then the legs are built off the bottom frame, the top frame is then placed on top and secured to the legs.
*The green pieces are screw strips. These provide limited load strength but serve to make assembly easier and help keep the stand square.
*The blue piece between the upper rails (red) works to keep the upper rails from twisting.
Ok, now to the cut list:
First off: The calculations below are based off of a stand that is "W" inches wide X "D" inches front-to-back X "H" inches high.
(2) Red - Upper Rails: Length = W
These will be sized according to length: 2X4 for 48" or less for smaller tanks (Rule of thumb is 75g-90g); 2X6 up to 72" with 125g-150g being acceptable; For longer spans and larger tanks 2X8s are recommended.
(2) Yellow - Upper Ends: Length = D-3"
Theses will be made of the same material as the upper rails.
(4) Green - Screw Strips: Length = H-2"
These 2X4s are shorter then the tank is tall.
(8) Purple - Uprights: Length varies:
- 2X4 Upper Rails: Length = H -7"
- 2X6 Upper Rails: Length = H-9"
- 2X8 Upper Rails: Length = H-10.75"
These 2X4s support the weight of the tank. The ones on the short sides of the stand provide a flat surface for attaching a plywood facing and while they do provide some strength, they are optional.
(2) Orange - Bottom Rails: Length = W
These 2X4s act to spread the weight of the tank over a larger area.
(3) Blue - Bottom Ends: Length = D-3"
Covering the sides of the stand with plywood will help to stiffen the stand against twisting and shifting. Doors can be mounted to the legs as desired.
So there it is. 21 pieces in 6 lenghts equals a tank stand that should fit the bill for most people. There are other plans out there but this is a simple design using simple tools and common wood sizes. It may not suit everyone's application but it should fit the bill for most common size tanks.
Things to note:
A 2X4 is actually 1.5" X 3.5"; a 2X6 is actually 1.5" X 5.5"; and a 2X8 is actually 1.5" X 7.25".
Making a beam made up of two boards side by side is twice as strong as each of the individual boards. For a 48" span, a 2X4 supporting 1000#s deflects 0.269" while a 2X6 only deflects 0.069" and a 2X8 deflects 0.030". That said, it is much better to go up in size then it is to double up.
When assembling the stand, be sure all of the pieces have square cut ends and that they are as straight as possible. If one of the long boards for the top frame (red above) has a crown (bows up when stood on edge), be sure to place the crown up. Glue will help bond the pieces together and coated decking screws will resist rusting. Clamping the pieces together and pre-drilling the holes will help make assembly easier.
Pocket drilling the legs (purple) can eliminate the need for the screw strip (green) but I would make sure to skin the stand on three sides to keep it from racking/twisting. Also, be sure to screw both leg pieces together on the corner for added strength."
HERE IS LINK TO ENTIRE THREAD:http://reefcentral.com/forums/showthread.php?s=&threadid=1169964&perpage=25&pagenumber=1
Please give me your feedback.
